How To Fix Beats Studio Headphones?

How To Fix Beats Studio HeadphonesBeats studio headphones can last for decades as a quick fix can restore normal function without reaping the unit apart. To breathe new life into Beats cans, tool up with screwdrivers, plastic opening equipment, and a soldering toolkit.

Replace spent batteries with a fresh pair; give a face-lift to ear cushion, headband, jack, motherboard, and speakers. Rather than nickel-and-dime oneself to death with a brand new set of cans every time you hit a snag, you should know how to fix beats studio headphones.

The market seethes with new components for hinges, headband, non-functional controls, charger port, and ear pads. Replacements resuscitate audio performance, wearing comfort and mechanical functionality. Our guide equips you with a fresh pair of eyes to put in order sound quality and construction without feeling the pinch.

8 Things To Consider About How To Fix Beats Studio Headphones:

1. Ear pads/cushion Replacement

If you misplace, break or begrime ear cushions, you can restore luxurious comfort with durable and soft, high elasticity replacements. You can procure replacement beats studio wireless replacement earpads with interlocking rings that make them interchangeable.

Consider earpads made from premium-grade leather or foam with noise canceling properties. Use a knife to detach the padding from the unit. Slough off adhesive remnants for a polished surface that attaches earpads without gaps. The replacement right side ear pad comes with a crevice for the USB port.

Align crevices with double dowels on the top left and the base right. Next, peel the adhesive and ensconce in the ear pads without the slightest gap. Use a few bulky books to exert the optimum pressure without twisting the unit’s headband.

2. Headband Repair From Start to Finish

To replace, first, peel the rubber to reach the cushion and pop it out with tweezers or knife.

Snap out the tabs to release the cushion without a hassle. You will remain with two pieces, including the cable. The improved cable can last for decades.

Align the replacements and go ahead to mount it on one side and thread through a screw.

After securing one side, snap in the cushion over the cable and press the top part to get the bottom snugly fixed in place. Slip the rubber back to the plastic clip. Shift it for the two ends to settle in position.

Realign and remove the screws if you have to tuck in the rubber tabs.

3. Fix Up Broken Speaker/Driver

  • Arm yourself with a soldering iron, knife, screwdriver and a new speaker for the headphones to get the ball rolling.
  • Start by removing the wire and the batteries. You won’t interfere with anything else.
  • Remove the ear pad of the broken side. Use the screwdriver to detach the screws. Handle with extra care as the magnet tends to pull loosened screws inside.
  • Now comes the hardest part, removing the speakers. Use a knife to severe bands and remove the wires from the speaker.
  • Take the new speaker and snug it into place, use the solder to connect the wires. Inside the speaker back and use glue to attach. Put the screws back, ear pads and return everything with a tight seal.

4. Put in Shape Metal Hinge

Tool up with long nose pliers or any handheld item with a sturdy edged metal tip.

  1. Take the unit and expose the hinges by separating the ear muffs from the headband. Locate the pin of the hinge where the arms of the ear muffs intersect with the headband.
  2. Wield the long nose pliers and lightly lift the ends of the metal rod facing the headband separately. It tightens the headband to prevent it from wobbling around.
  3. Stretch the arms of the ear pads from the headband to the maximum.
  4. Stretch the ear pads away from the unit like when you have them on. Grasp it by the headband and lightly shake it to see if it remains securely in position.

5. Charging Port & Micro USB Jack Replacement

Cut the defective jack plug off with wire cutters, then pull the cables apart and strip a few inches from the external insulation.

You will see three exposed wires at the tip of the cable, left, right or ground.

Use the soldering tool to fix wires and avoid blobs. Unscrew the unit from the replacement jack plug; slide the outer cover across the wire, with the threaded tip closer to the solder joint.

Fix the wires to the pins with the solder on the unsheathed innards of the jack plug. Solder the ground pin to the corresponding wire and the binary signal wires onto the two remaining pins. Crimp the edge of the ground tag securely and reassemble the unit.

6. Repairing Unit After Water Contact or Immersion

If water seeps into electronics, the corrosion can cause irreparable damage. You must respond quickly to shake off any moisture. Peel off covers without any tools using a screwdriver. To go DIY, salt away isopropyl alcohol, towels, and detach all batteries after disassembling.

  1. If you submerge or drench your cans in water, dip into 100% isopropyl solution to bath in intensively. You can use compressed air to blow off the water.
  2. Avoid a powerful air stream as it damages delicate components. To keep it as dry as a bone, slip it into a bag with fresh silica gel and seal the compartment before exposing it to direct sunlight.
  3. Recharge the battery, and the unit will churn out sound at full pelt.

7. Distorted Sound & Echoes

Snapping, crackling and popping speaker taints sound quality while the volume remains too low or high. Most audio flaws dwindle away with simple troubleshooting. You can also install a new driver by taking apart the headphones to reach the assembly.

  1. Turn on your headphones and ensure you play some music to adjust the volume both on your device and speaker.
  2. Ensure the cable connects properly.
  3. You can also troubleshoot Bluetooth to belt out the most suitable volume.
  4. Plugged-in acoustic feedback between the speakers and phone microphone can cause echoes.
  5. If you pair your speakers with Bluetooth and capture echoes, troubleshoot.

8. Beats Studio Headphones Repair Basics

The unit’s housing packs the lithium battery, charging circuit, motherboard, noise-canceling microphone and LED controls

Use a multi-meter to test positive and negative charges, if voltage reads above 4v. It has a full charge

After dismantling the unit, pore over the motherboard for any symptoms of component flaws like blown-up marks or melted capacitors

If the headset has a damaged chip or capacitor, you can engage an expert

Restore the pieces of tape when assembling to prevent wires from repositioning

Electronic repairers offer salvageable components at throw-away prices

For water-related challenges, switch off the unit to cut off circuit

Final Verdict

The tiny pieces of metal, rubber and plastic take a beating as you walk, twist or curl the cable. If you know the ins and outs of how to fix beats studio headphones, you can make amends rather than cough up more bucks for a new pair of cans.

Once you diagnose the root of the problem, you can replace or repair your investment to run at full pelt again. Studio headphones come with a user manual that can help you familiarize yourself with anatomy and key components. Other mines of information include video tutorials exploring how to replace or mend a specific part.

About the author

Related

JOIN THE DISCUSSION